Nationwide Service
Fire Alarm Shop Drawings & Submittal Documents — Indiana
NICET Level IV-certified fire alarm shop drawings in Indiana, produced under NFPA 72 Chapter 7 and delivered submittal-ready for AHJ review.
Professional fire alarm shop drawings Indiana
Titan Fire Protection produces fire alarm shop drawings in Indiana and across the country for contractors, MEP engineers, and architects. Our fire alarm drawings in Indiana are built to NFPA 72 Chapter 7 — the documentation standard fire marshals and building officials expect on every submittal package.
Whether you need fire alarm permit drawings in Indiana for new construction, a renovation, or a panel replacement, our NICET fire alarm drawings in Indiana are reviewed, signed by a NICET Level IV designer, and immediately ready for AHJ review.
What fire alarm shop drawings are — and why they’re required
Fire alarm shop drawings are the contractor’s coordination document. They translate the engineer of record’s performance specification and life-safety design intent into a site-specific, device-level submittal package — showing exact device placement, wiring, circuit pathing, riser diagrams, and panel programming requirements.
In nearly every jurisdiction, the Authority Having Jurisdiction (AHJ) — typically the local fire marshal or building department — must review and approve fire alarm shop drawings before a permit is issued or installation begins. An incomplete or non-conforming submittal is the most common cause of permit delays.
NFPA 72 Chapter 7 documentation requirements
NFPA 72 — the National Fire Alarm and Signaling Code — has required formal fire alarm system documentation as a condition of installation since its earliest editions. Since the 2013 edition, Chapter 7 has been the controlling documentation chapter and has remained so through the 2016, 2019, and 2022 editions.
Chapter 7 specifies what a complete fire alarm submittal must contain:
- Site-specific shop drawings with device locations and circuit pathing
- Sequence of operations and input/output matrices
- Battery standby and voltage-drop calculations
- Notification appliance circuit (NAC) loading and audibility coverage
- Manufacturer data sheets for every listed component
- Riser diagrams showing all circuits, zones, and interconnections
A submittal missing any of these is, by definition, incomplete. IFC Section 907 and IBC Section 901 reinforce NFPA 72 by reference, tying it to occupancy classification, egress design, and required notification systems.
What’s included in every Titan drawing set
Every set of NICET fire alarm drawings in Indiana includes the following sheets, sized and coordinated to the project:
- Cover Sheet Project data, vicinity map, and drawing index.
- Requirements Applicable codes, general notes, and state or local amendments.
- System Calculations Battery standby and alarm load, voltage drop, and notification appliance circuit loading.
- Details Device mounting requirements, installation details, and clearance requirements.
- Panel Details & I/O Matrix Control panel wiring details and a complete input/output matrix for every initiating and notification circuit.
- Riser Diagram All circuits, zones, and system interconnections on a single coordinated diagram.
Supported fire alarm panel manufacturers
Drawing sets are produced for the following panel platforms. Panel selection can be made by the contractor or recommended by Titan based on project requirements and jurisdiction.
- Potter
- Fire-Lite
- Silent Knight
- Edwards
- Silent Knight Farenhyt
- Notifier
Code compliance for Indiana fire alarm permit drawings
- NFPA 72 — National Fire Alarm and Signaling Code
- IFC — International Fire Code
- IBC — International Building Code
- NFPA 101 — Life Safety Code (where applicable)
- NFPA 70 — National Electrical Code (where applicable)
- State and local amendments are incorporated when the jurisdiction is identified.
Credentials
NICET Level IV design — built into every set
Every set of fire alarm drawings in Indiana is produced and reviewed under the supervision of our NICET Level IV-certified designer — the highest certification available in the Fire Alarm Systems discipline. Most AHJs and an increasing number of architectural and MEP firms require a minimum of NICET Level III to prepare and sign shop drawings; Titan exceeds that requirement on every project.
Designing in Indiana yourself?
Fire alarm design, done right inside AutoCAD.
CodeGreen CAD Tools, from Titan's NICET Level IV designer: detector spacing and SLC wiring, risers, the matrix with battery and circuit calcs, templates, sheet index and keynotes. AutoCAD and AutoCAD LT 2024 and newer.
Ready to start your Indiana fire alarm drawing project?
Submit your project documents and our NICET Level IV design team will respond within one business day with a quote or any additional information needed to produce a complete, code-compliant submittal package.